BradCee fantastic VCI 100 (1.2fw) 4 deck control (TPro)

Ladies and Gentleman of the VCI100 firware version 1.2 persuasion, i present my awesome new map for 4 deck control on the VCI

VCI 100 [Brad_Cee Edition] V3.0

Version 1 of this map was on T3, 2 was on Tpro, but got messy so tidied up and is now 3, tsi is called V2 though, as Tpro 2nd version.

Hit the thumbnail for the mapping layout (can't get the sizing right ), also it's the overlay i was going to have. glad i changed my mind

Notable details;
EQ buttons, are set as a toggle, hit once for each of the decks a/c or b/d - the little red lights on the left light up to show the decks that you have eq control over.

The little black buttons on the left do an 'echo freeze' using delay in fx bank 1 in advanced mode

Transform buttons are done with a gater in fx bank 2, advanced mode

FX banks 3 and 4 are beatslicers (advance mode), 3 is used for Sampler 1/Deck C page and 4 is used for Sampler 2/Deck D page in the sampler section

The fx banks start in advanced mode, but the middle light section in the 'sampler bit' (formerly effects on default map) controls fx for decks a and b. Hit the related little button, it'll switch the fx bank into chained, and assign to that deck. First 2 buttons are presets for A, and second 2 are presets for B, the knobs line up with the screen.
When you 'activate' deck A's fx, the delay moves to fx bank 2 so you still have echo freeze function.

On the sampler section, after copying a deck, holding shift and turning the 'sampler deck' up will turn down and stop the deck you just copied.
Holding shift and hitting either little button on sampler 1 or 2 does a 'quick sample'. In that is assigns the Beatslicer in that related fx bank (3 or 4) to that deck (A or B). This is useful for when you have a loop playing over another track, want to hold it for a bit then mix in something else.

In juggle/mash for decks a and b, the lights under the transform will light up (might be wrong way round, i hot wired a couple of new leds into middle of vci for this - if they are, find the outputs for modifiers 5 and 6 and swap the midi notes around A#4 and B4 i believe). You HAVE to press the Mash button (loop ordinarily) to set the masher (and reverb) on. Hold shift and press the (now) cue buttons to activate preset parameters. This won't work if you don't press mash (the transform light will flash when you have). This has been done as a fail safe, as when it jumps into chained fx mode it loads the previously used combo, if this is the wrong one, it sounds shit.
Play toggle and the Cue point buttons work whether mash mode is on or off. The juggle mode 'knobs' have to be passed about halfway to to set the fx bank to chained mode

You can't echo freeze more than 1 deck at a time, same with transform.

After pressing the crate button the jogs browse, left one for favorites, right one for up/down the list.

You can't use chained fx on decks A and B at the same time, as they share the controls.

When pressing anything that is labelled as 'sampler', it sets the beatslicer to 8 beats, and sets an 8 beat loop on the sampled track, a la eans midi fighter map. If a loop is already in place, holding shift will stop the 'loop active' mode from toggling on decks C and D.

There are some C and D 'quick play' bits. The pitch faders are now fader start, this starts the deck and fades it in, and the middle buttons have a quick sample for C and D with access to the pattern and buzz parameters.

I plan to create a dicer 'add on' map for x-fade assignments and c and d cue points. plus something else, but not decided what yet.