Reply to Mr. Blenderson's Dicer Mapping for Traktor

Hey all...
I couldn't get the DJTT mapping to load properly on my computer so I just made my own. It's somewhat based on the DJTT mapping but with some added bonuses.

You will need 4 chained effects devices for this mapping. The TSI should load the proper effects but if it does not, load them as follows:
Effect Unit 1: Beatmasher, Filter LFO, Delay
Effect Unit 2: Beatmasher, Filter LFO, Delay
Effect Unit 3: Flanger, Gater, Digital Lofi
Effect Unit 4: Flanger, Gater, Digital Lofi

To make the effect buttons work make sure send 1 and 3 are always on for Deck A and send 2 and 4 are always on for Deck B.

Here's how it works:

Layer 1 - Hotcues
Buttons 1-5: Hotcue 1-5. Each button lights up red if a Hotcue is stored. If it is not lit up you can store one by pressing the button.
Buttons 1-5 Shifted: Delete Hotcues 1-5. Each button lights up dim red if a Hotcue is stored and pushing the button will delete the corresponding Hotcue.

Layer 2:
Button 1: Multi loop. Press once for loop in point, it will turn loop on and light up yellow. Press a second time to set loop out point. While it is looping, press a third time to set the loop to 1 bar and then keep pressing to half the loop length.
Button 1 shifted turns loop off. When button 1 is yellow loop is active.
This one is a bit complicated and if anyone has any questions let me know.
It will make more sense if you just play around with it.

Buttons 2 - 5: Loop roll (light up green)
Button 2: 1/4 note Button 3: 1/8 note Button 4: 1/16 note Button 5: 1/32 note

Buttons 2 - 5 shifted: Quick Loops (light up yellow)
Button 2: 8 bar Button 3: 4 bar Button 4:2 bar Button 5: 1 bar
Note that Button 1 lights up yellow to indicate that loop mode is active. Whenever loop mode is active the multi-loop function (halving loop length) is available, and you can turn loop off by pressing shift+button 1.

Layer 3: Effects

Button 1: Filter sweep
Button 2: Delay
Button 3: Flanger
Button 4: Gater
Button 5: Digital Lofi

Buttons will momentarily turn on effects. Shift+button will toggle them on/off. Buttons will light up orange to indicate that effect is on. You can turn off an effect by tapping the lit button (do not need to do shift+button).



Mapping Chart:

Layer 1 (RED)
1. Hotcue 1
2. Hotcue 2
3. Hotcue 3
4. Hotcue 4
5. Hotcue 5

Layer 1 Shifted (DIM RED)
1. Delete Hotcue 1
2. Delete Hotcue 2
3. Delete Hotcue 3
4. Delete Hotcue 4
5. Delete Hotcue 5

Layer 2 (GREEN)
1. Multi-Loop (YELLOW)
2. Looproll 1/4
3. Looproll 1/8
4. Looproll 1/16
5. Looproll 1/32

Layer 2 Shifted (YELLOW)
1. Loop Off
2. 8 Bar Loop
3. 4 Bar Loop
4. 2 Bar Loop
5. 1 Bar Loop

Layer 3 (ORANGE)
1. Filter Sweep Hold
2. Delay Hold
3. Flanger Hold
4. Gater Hold
5. Digital Lofi Hold

Layer 3 Shifted (Orange)
1. Filter Sweep On/Off
2. Delay On/Off
3. Flanger On/Off
4. Gater On/Off
5. Digital Lofi On/Off


Please let me know if you have any questions, suggestions, or feedback. Hope some of you enjoy it! I'm having a ton of fun with it.