Vci-100 Up Fader

Home :: Reviews of DJ equipment :: Vci-100 Up FaderReply
Vci-100 Up Fader
Posted on: 08.01.2009 by Gavin Armstrong
So my up fader on my vci-100 is goin out . when its at the top of the channel traktor fader goes to the top then suddenly jumps to the middle.It must have a slight bend in the vci connection, cause the software can't determine if its at the top or middle.It still works fine, i just cant push on the fader to the top to hard or traktors mixer's up fader drops back down to the middle

is there some thing at all to fix my controller so that traktor can read it right
Elia Ajram
11.01.2009
Originally Posted by rjw

So it might just be a dirty connection inside
It was most definitely some dirt in the fader itself. Glad to hear its working again, but I would never use WD-40. Ideally, you should open up the fader (if thats even possible with these fader) and wipe it down with a strong alcohol, then apply a silicone based lubricant.
Gavin Armstrong
11.01.2009
Originally Posted by rjw
I've had problems with my fader before. It was after some beer got into my vci! :S If I moved the fader all the way to the top Traktor would believe it was at the BOTTOM, not very good.... If I tried to slam that fader up to the top, the track would cut out altogether lol.

Anyway, I fixed it by spraying a load of WD40 into the fader. wiggled it up and down a bit. picked up and tilted the vci (over an old cloth) to let the excess drip out. Then, after leaving it for 5-10mins I kept working the fadrer back and forth to clear any residue or dirt and soon enough - it was working again! woop

So it might just be a dirty connection inside
ok i believe your on to something ,,, but im kind of scared to spray wd40 into it ,,,you said that you sprayed in the where the up fader went up and down ,,, then turned the vci-100 up side down and let it drip out ,,& wiggled the fader around ,,,,,do i have that right
Gavin Armstrong
10.01.2009
Originally Posted by DvlsAdvct
Just curious, in your .TSI what type of controller is selected for the fader?

umm im not at home right now ,,, & not to sure what that means but im sure its a vci-100 selected all the way,,,, i believe its the acatual vci-100 up fader needs to be replaced. its must be bent a little cause if i press up on it when it all the way at the top it cuts out then traktors mixer jumps to the middle. I have the same problem with regualr mixers.. i believe it slighlty bent ,, its not real bad ,, i can still use it but i want it fixed
Gavin Armstrong
08.01.2009		So my up fader on my vci-100 is goin out . when its at the top of the channel traktor fader goes to the top then suddenly jumps to the middle.It must have a slight bend in the vci connection, cause the software can't determine if its at the top or middle.It still works fine, i just cant push on the fader to the top to hard or traktors mixer's up fader drops back down to the middle

is there some thing at all to fix my controller so that traktor can read it right
Elia Ajram
11.01.2009
Originally Posted by rjw

So it might just be a dirty connection inside
It was most definitely some dirt in the fader itself. Glad to hear its working again, but I would never use WD-40. Ideally, you should open up the fader (if thats even possible with these fader) and wipe it down with a strong alcohol, then apply a silicone based lubricant.
Gavin Armstrong
11.01.2009
Originally Posted by rjw
I've had problems with my fader before. It was after some beer got into my vci! :S If I moved the fader all the way to the top Traktor would believe it was at the BOTTOM, not very good.... If I tried to slam that fader up to the top, the track would cut out altogether lol.

Anyway, I fixed it by spraying a load of WD40 into the fader. wiggled it up and down a bit. picked up and tilted the vci (over an old cloth) to let the excess drip out. Then, after leaving it for 5-10mins I kept working the fadrer back and forth to clear any residue or dirt and soon enough - it was working again! woop

So it might just be a dirty connection inside
ok i believe your on to something ,,, but im kind of scared to spray wd40 into it ,,,you said that you sprayed in the where the up fader went up and down ,,, then turned the vci-100 up side down and let it drip out ,,& wiggled the fader around ,,,,,do i have that right
Riccardo gava
09.01.2009		I've had problems with my fader before. It was after some beer got into my vci! :S If I moved the fader all the way to the top Traktor would believe it was at the BOTTOM, not very good.... If I tried to slam that fader up to the top, the track would cut out altogether lol.

Anyway, I fixed it by spraying a load of WD40 into the fader. wiggled it up and down a bit. picked up and tilted the vci (over an old cloth) to let the excess drip out. Then, after leaving it for 5-10mins I kept working the fadrer back and forth to clear any residue or dirt and soon enough - it was working again! woop

So it might just be a dirty connection inside
Roberto Viccione
09.01.2009		no no, not what I mean.

In your .TSI file you can select the kind of controller (Jog Wheel, Analog Knob/Fader, Relative Knob, etc. etc. etc.). I want to know what control attribute is selected for that entry in the .TSI.
Gavin Armstrong
10.01.2009
Originally Posted by DvlsAdvct
Just curious, in your .TSI what type of controller is selected for the fader?

umm im not at home right now ,,, & not to sure what that means but im sure its a vci-100 selected all the way,,,, i believe its the acatual vci-100 up fader needs to be replaced. its must be bent a little cause if i press up on it when it all the way at the top it cuts out then traktors mixer jumps to the middle. I have the same problem with regualr mixers.. i believe it slighlty bent ,, its not real bad ,, i can still use it but i want it fixed
Roberto Viccione
08.01.2009		Just curious, in your .TSI what type of controller is selected for the fader?

<< Back to Reviews of DJ equipment Reply

Copyright 2012-2023
DJRANKINGS.ORG n.g.o.
Chuo-ku, Osaka, Japan

Created by Ajaxel CMS

Terms & Privacy