HELP!! Can upgrade to 1.3 but not 1.4
HELP!! Can upgrade to 1.3 but not 1.4 Posted on: 21.04.2011 by Daren Masso Have tried to upgrade to firmware v1.4, 1.3.1, 1.3.2 & 1.3.3 but was unsuccessful. I get the message below which, although it says the upgrade was a success, it actually wasn't Flash Development Toolkit and flash programming components are provided without support OS: Windows XP [Admin] FCF Settings Applied: H8/3052F, (C:\Program Files\Renesas\FDT4.05\kernels\ProtB\3052\Renesas\1 _2_00\) FDT API initialised: version 4, 05, 00, 008 FCF Settings Applied: H8/3052F, (C:\Program Files\Renesas\FDT4.05\kernels\ProtB\3052\Renesas\1 _2_00\) Clock Frequency (External) = 24.0000MHz, Clock Mode = 0, CKM = 1, and CKP = N/A Connecting to device 'H8/3052F' on 'COM2' Configuration: 'BOOT Mode' connection - using emulated interface Opening port 'COM2' ... Loading Comms DLL Loaded Comms DLL Initiating BOOT SCI sequence Attempting 9600 Received immediate response from device: 0xAA Using micro-Kernel : 'C:\Program Files\Renesas\FDT4.05\kernels\ProtB\3052\Renesas\1 _2_00\uGen3052.cde' Downloading and verifying micro kernel... Device is erasing... Erase Timeout value set to 21 seconds Erase Successful micro-Kernel download successful Sending inquiry for getting line size Buffer size has been set to default (128 bytes) Sending selection of device command Selection of Device - Device selected, code 0302 Sending selection of clock mode Sending selection of clock mode Selection of Clock Mode - Clock selected, code 0 Changing baud rate to 38400 bps Set baud rate value = 38400 Downloading main kernel 'C:\Program Files\Renesas\FDT4.05\kernels\ProtB\3052\Renesas\1 _2_00\Genm3052.cde' Main kernel download complete... Connection complete Processing file :"I:\VCI1001_4 (1)\VCI100-DaveX-1.4.mot" Operation on User Flash Downloaded the operation module Writing image to device... [0x00000000 - 0x0000907F] Writing image to device... [0x00009080 - 0x0000917F] Writing image to device... [0x00009180 - 0x00009AFF] Data programmed at the following positions: 0x00000000 - 0x0000907F Length : 0x00009080 0x00009080 - 0x0000917F Length : 0x00000100 0x00009180 - 0x00009AFF Length : 0x00000980 38.75 K programmed in 109 seconds Image written to device Disconnecting Disconnected There are only 3 lines with "Writing image to device...." whereas (I believe) there should be 6. Bizarrely I tried to upgrade to 1.3 and that was successful: Flash Development Toolkit and flash programming components are provided without support OS: Windows XP [Admin] FCF Settings Applied: H8/3052F, (C:\Program Files\Renesas\FDT4.05\kernels\ProtB\3052\Renesas\1 _2_00\) FDT API initialised: version 4, 05, 00, 008 FCF Settings Applied: H8/3052F, (C:\Program Files\Renesas\FDT4.05\kernels\ProtB\3052\Renesas\1 _2_00\) Clock Frequency (External) = 24.0000MHz, Clock Mode = 0, CKM = 1, and CKP = N/A Connecting to device 'H8/3052F' on 'COM3' Configuration: 'BOOT Mode' connection - using emulated interface Opening port 'COM3' ... Loading Comms DLL Loaded Comms DLL Initiating BOOT SCI sequence Attempting 9600 Received immediate response from device: 0xAA Using micro-Kernel : 'C:\Program Files\Renesas\FDT4.05\kernels\ProtB\3052\Renesas\1 _2_00\uGen3052.cde' Downloading and verifying micro kernel... Device is erasing... Erase Timeout value set to 21 seconds Erase Successful micro-Kernel download successful Sending inquiry for getting line size Buffer size has been set to default (128 bytes) Sending selection of device command Selection of Device - Device selected, code 0302 Sending selection of clock mode Sending selection of clock mode Selection of Clock Mode - Clock selected, code 0 Changing baud rate to 38400 bps Set baud rate value = 38400 Downloading main kernel 'C:\Program Files\Renesas\FDT4.05\kernels\ProtB\3052\Renesas\1 _2_00\Genm3052.cde' Main kernel download complete... Connection complete Processing file :"I:\vci-100se_13_firmware\VCI-100SE_1.3_Firmware.mot" Operation on User Flash Downloaded the operation module Writing image to device... [0x00000000 - 0x000000FF] Writing image to device... [0x00000200 - 0x0000647F] Writing image to device... [0x00008000 - 0x0000807F] Writing image to device... [0x00009000 - 0x0000907F] Writing image to device... [0x00009080 - 0x0000917F] Writing image to device... [0x00009180 - 0x00009AFF] Data programmed at the following positions: 0x00000000 - 0x000000FF Length : 0x00000100 0x00000200 - 0x0000647F Length : 0x00006280 0x00008000 - 0x0000807F Length : 0x00000080 0x00009000 - 0x0000907F Length : 0x00000080 0x00009080 - 0x0000917F Length : 0x00000100 0x00009180 - 0x00009AFF Length : 0x00000980 27.75 K programmed in 77 seconds Image written to device Disconnecting Disconnected Does anyone know why it would work for 1.3 and not the rest? Any solutions to my problem would be much appreciated...have spent days trying to solve it | |
Daren Masso 21.04.2011 | Have tried to upgrade to firmware v1.4, 1.3.1, 1.3.2 & 1.3.3 but was unsuccessful. I get the message below which, although it says the upgrade was a success, it actually wasn't Flash Development Toolkit and flash programming components are provided without support OS: Windows XP [Admin] FCF Settings Applied: H8/3052F, (C:\Program Files\Renesas\FDT4.05\kernels\ProtB\3052\Renesas\1 _2_00\) FDT API initialised: version 4, 05, 00, 008 FCF Settings Applied: H8/3052F, (C:\Program Files\Renesas\FDT4.05\kernels\ProtB\3052\Renesas\1 _2_00\) Clock Frequency (External) = 24.0000MHz, Clock Mode = 0, CKM = 1, and CKP = N/A Connecting to device 'H8/3052F' on 'COM2' Configuration: 'BOOT Mode' connection - using emulated interface Opening port 'COM2' ... Loading Comms DLL Loaded Comms DLL Initiating BOOT SCI sequence Attempting 9600 Received immediate response from device: 0xAA Using micro-Kernel : 'C:\Program Files\Renesas\FDT4.05\kernels\ProtB\3052\Renesas\1 _2_00\uGen3052.cde' Downloading and verifying micro kernel... Device is erasing... Erase Timeout value set to 21 seconds Erase Successful micro-Kernel download successful Sending inquiry for getting line size Buffer size has been set to default (128 bytes) Sending selection of device command Selection of Device - Device selected, code 0302 Sending selection of clock mode Sending selection of clock mode Selection of Clock Mode - Clock selected, code 0 Changing baud rate to 38400 bps Set baud rate value = 38400 Downloading main kernel 'C:\Program Files\Renesas\FDT4.05\kernels\ProtB\3052\Renesas\1 _2_00\Genm3052.cde' Main kernel download complete... Connection complete Processing file :"I:\VCI1001_4 (1)\VCI100-DaveX-1.4.mot" Operation on User Flash Downloaded the operation module Writing image to device... [0x00000000 - 0x0000907F] Writing image to device... [0x00009080 - 0x0000917F] Writing image to device... [0x00009180 - 0x00009AFF] Data programmed at the following positions: 0x00000000 - 0x0000907F Length : 0x00009080 0x00009080 - 0x0000917F Length : 0x00000100 0x00009180 - 0x00009AFF Length : 0x00000980 38.75 K programmed in 109 seconds Image written to device Disconnecting Disconnected There are only 3 lines with "Writing image to device...." whereas (I believe) there should be 6. Bizarrely I tried to upgrade to 1.3 and that was successful: Flash Development Toolkit and flash programming components are provided without support OS: Windows XP [Admin] FCF Settings Applied: H8/3052F, (C:\Program Files\Renesas\FDT4.05\kernels\ProtB\3052\Renesas\1 _2_00\) FDT API initialised: version 4, 05, 00, 008 FCF Settings Applied: H8/3052F, (C:\Program Files\Renesas\FDT4.05\kernels\ProtB\3052\Renesas\1 _2_00\) Clock Frequency (External) = 24.0000MHz, Clock Mode = 0, CKM = 1, and CKP = N/A Connecting to device 'H8/3052F' on 'COM3' Configuration: 'BOOT Mode' connection - using emulated interface Opening port 'COM3' ... Loading Comms DLL Loaded Comms DLL Initiating BOOT SCI sequence Attempting 9600 Received immediate response from device: 0xAA Using micro-Kernel : 'C:\Program Files\Renesas\FDT4.05\kernels\ProtB\3052\Renesas\1 _2_00\uGen3052.cde' Downloading and verifying micro kernel... Device is erasing... Erase Timeout value set to 21 seconds Erase Successful micro-Kernel download successful Sending inquiry for getting line size Buffer size has been set to default (128 bytes) Sending selection of device command Selection of Device - Device selected, code 0302 Sending selection of clock mode Sending selection of clock mode Selection of Clock Mode - Clock selected, code 0 Changing baud rate to 38400 bps Set baud rate value = 38400 Downloading main kernel 'C:\Program Files\Renesas\FDT4.05\kernels\ProtB\3052\Renesas\1 _2_00\Genm3052.cde' Main kernel download complete... Connection complete Processing file :"I:\vci-100se_13_firmware\VCI-100SE_1.3_Firmware.mot" Operation on User Flash Downloaded the operation module Writing image to device... [0x00000000 - 0x000000FF] Writing image to device... [0x00000200 - 0x0000647F] Writing image to device... [0x00008000 - 0x0000807F] Writing image to device... [0x00009000 - 0x0000907F] Writing image to device... [0x00009080 - 0x0000917F] Writing image to device... [0x00009180 - 0x00009AFF] Data programmed at the following positions: 0x00000000 - 0x000000FF Length : 0x00000100 0x00000200 - 0x0000647F Length : 0x00006280 0x00008000 - 0x0000807F Length : 0x00000080 0x00009000 - 0x0000907F Length : 0x00000080 0x00009080 - 0x0000917F Length : 0x00000100 0x00009180 - 0x00009AFF Length : 0x00000980 27.75 K programmed in 77 seconds Image written to device Disconnecting Disconnected Does anyone know why it would work for 1.3 and not the rest? Any solutions to my problem would be much appreciated...have spent days trying to solve it |
Daren Masso 26.04.2011 | Bump. Does anyone have any ideas? I'm stumped! |
<< Back to DJ TechTools' VCI-100 FAQReply