Paddy's APC40 Mapping for TPro (yup another one :D)

Home :: Post and find Controller Mappings :: Paddy's APC40 Mapping for TPro (yup another one :D)Reply
Paddy's APC40 Mapping for TPro (yup another one :D)
Posted on: 04.11.2010 by Nedra Fresneda
Finally sat down and made the tutorial image for it hehe.
I'm currently selling the akai so i don't believe there will be an update, but i'm willing to provide support and help development in new versions of it.

Made with version 1.2.4

TSI Download
Hi Res Image



Notes:

APC works in regular (not dumb mode) in order to keep the 9 device control banks without having to get into heavy modifier use or any 3rd pary software.

This mapping uses “send monitor state" heavily and works without an issue on mac. PC users should search the community for the fix. As a general rule, increase your latency 1-2ms to relieve some of the extra cpu used for midi traffic.

Deck control selection buttons are duplicaded in order to make switching between them more confortable and to have a better visual aid.
*Hotcue 1 is a grid marker, if no marker has been asigned or you want to move it delete hotcue 1 (shift+hotcue), press 1 time to place a hotcue and press again to turn it into a grid marker
*FX work in ADVANCED mode, there is plenty of room to map them as chained as well, having both options available.
*EQs leds work in pan mode.
*Fx leds work in full mode and are updated along with the knob position when scrolling through fx (no need for soft takeover)
*Auto Loop is green when engaged and turns yellow when off.
*Beat +/- jump size corresponds to the one selected in Traktor.
*To shitch between left (1/3) and right (2/4) fx units use track 1 and 2 buttons,
*To use EQ for the lower decks press the track select 3 and device control replicates EQ A/B layout (the 8 buttons in bank 3 are free for assignment)
*All buttons shown in the image as dark grey are free, being my intention to use them to control sample decks and loop recorder in the following update.
*Crossfader is mapped to monitor mix to relieve avoid overuse of the cuemix knob (and because IMO it flymsy for any other precision use)

Browse (former Shift Button) - Toggle
*Fullscreen browser
*In this mode Cue Stop buttons are flashing red and act as Load Deck.

Shift (former Tap Tempo) – Momentary
*List select now works as pitch control for the deck in focus (0,01 resolution with acceleration)
*Sync button now reasings the master tempo to te corresponding deck.
*Bend +/- flash yellow and moves the Beatgrid in short increments (autorepeat)
*Beat +/- flash green and changes the loop length
*Hold down shift + hotcue to deleted one

PS: I don't remember if i removed it or not, but ignore the OLD APC midi page (my old mapping)
Nedra Fresneda
03.07.2011
Originally Posted by djmior
have you been able to remap this template for use on traktor pro 2 yet??
Sorry, but I sold my APC on november to fund my current setup.
Nedra Fresneda
04.03.2011
Originally Posted by djmior
k..i must be asking a totally dumb question..
but how do you load the effects and better yet..how do you activate the advanced fx controls?

i'm trying out traktor for the first time..i know ableton live very well..but this traktor thing has me stumped
banks 1 & 2. the attached image describes which faders act as fx selectors. chained fx haven't been mapped.
Nedra Fresneda
25.02.2011
Originally Posted by ThePattern
Padi, any word on those endless knobs? How did you do the fx knobs with no soft takeover?
Using the APC in regular (not dumb mode) they update by themselves if you assign the OUT to the same CC. On top of that, CC+8 is Outs are mapped to have multiple leds light up like they do in Ableton.

This does make the knobs move "slower" as IN/OUTs are fighting each other and it get's worse as the latency increases, but at 2-10ms it didn't bother me.

Try setting the latency to something like 30ms and see what I mean.
Stephnie Godbole
25.02.2011
Originally Posted by padi_04
One last thing, it's the "Windows Friendly" version so the VU Meters were removed to avoid popping
Ah no problem. gonna run my stuff through mp3gain anyways and i usually have master out to -7
Stephnie Godbole
25.02.2011
Originally Posted by padi_04
It's the idea, but I sold the unit so can't map it myself.
well next month Ill have one so if needbe I can take your tsi and add it in when T2 is out
Nedra Fresneda
25.02.2011
Originally Posted by MuzicFreq
WOW NICE
Planning on making those 8 empty buttons below the deck be for the sample decks?
It's the idea, but I sold the unit so can't map it myself.
Stephnie Godbole
25.02.2011
Originally Posted by padi_04
Attached TSI & pic
WOW NICE
Planning on making those 8 empty buttons below the deck be for the sample decks?
Nedra Fresneda
09.11.2010
Originally Posted by robbiekurupt
howdy

i tried to import ur tsi but there is nothing on the file??? ive a few other mappings and they all load so it doesnt seem to be me or my laptop.

if u can have a look at it and let me know, id like to try urs out!!!
What version are you using? I just downloaded it and tested import on my mac and work pc. You need Traktor 1.2.4 or later.

The TSI file works
Nedra Fresneda
04.11.2010		Finally sat down and made the tutorial image for it hehe.
I'm currently selling the akai so i don't believe there will be an update, but i'm willing to provide support and help development in new versions of it.

Made with version 1.2.4

TSI Download
Hi Res Image



Notes:

APC works in regular (not dumb mode) in order to keep the 9 device control banks without having to get into heavy modifier use or any 3rd pary software.

This mapping uses “send monitor state" heavily and works without an issue on mac. PC users should search the community for the fix. As a general rule, increase your latency 1-2ms to relieve some of the extra cpu used for midi traffic.

Deck control selection buttons are duplicaded in order to make switching between them more confortable and to have a better visual aid.
*Hotcue 1 is a grid marker, if no marker has been asigned or you want to move it delete hotcue 1 (shift+hotcue), press 1 time to place a hotcue and press again to turn it into a grid marker
*FX work in ADVANCED mode, there is plenty of room to map them as chained as well, having both options available.
*EQs leds work in pan mode.
*Fx leds work in full mode and are updated along with the knob position when scrolling through fx (no need for soft takeover)
*Auto Loop is green when engaged and turns yellow when off.
*Beat +/- jump size corresponds to the one selected in Traktor.
*To shitch between left (1/3) and right (2/4) fx units use track 1 and 2 buttons,
*To use EQ for the lower decks press the track select 3 and device control replicates EQ A/B layout (the 8 buttons in bank 3 are free for assignment)
*All buttons shown in the image as dark grey are free, being my intention to use them to control sample decks and loop recorder in the following update.
*Crossfader is mapped to monitor mix to relieve avoid overuse of the cuemix knob (and because IMO it flymsy for any other precision use)

Browse (former Shift Button) - Toggle
*Fullscreen browser
*In this mode Cue Stop buttons are flashing red and act as Load Deck.

Shift (former Tap Tempo) – Momentary
*List select now works as pitch control for the deck in focus (0,01 resolution with acceleration)
*Sync button now reasings the master tempo to te corresponding deck.
*Bend +/- flash yellow and moves the Beatgrid in short increments (autorepeat)
*Beat +/- flash green and changes the loop length
*Hold down shift + hotcue to deleted one

PS: I don't remember if i removed it or not, but ignore the OLD APC midi page (my old mapping)
Karie Jose
03.07.2011		hmmmmmm...now that really sucks..
cause i'd love to be able to integrate the sample racks into the apc..i've modified your tsi file to support a 2 deck setup..if now i could only use the deck c/d functions to map the sample decks for c/d

you have any tips or tricks i can use to map it? ...anyone?
Nedra Fresneda
03.07.2011
Originally Posted by djmior
have you been able to remap this template for use on traktor pro 2 yet??
Sorry, but I sold my APC on november to fund my current setup.
Karie Jose
03.07.2011		have you been able to remap this template for use on traktor pro 2 yet??
Nedra Fresneda
04.03.2011
Originally Posted by djmior
k..i must be asking a totally dumb question..
but how do you load the effects and better yet..how do you activate the advanced fx controls?

i'm trying out traktor for the first time..i know ableton live very well..but this traktor thing has me stumped
banks 1 & 2. the attached image describes which faders act as fx selectors. chained fx haven't been mapped.
Karie Jose
04.03.2011		k..i must be asking a totally dumb question..
but how do you load the effects and better yet..how do you activate the advanced fx controls?

i'm trying out traktor for the first time..i know ableton live very well..but this traktor thing has me stumped
Nedra Fresneda
25.02.2011		scene launch buttons are free, you could try those
Julieta Cucinotta
25.02.2011		Ah... I was hoping to figure out something where I could set the cc only when I switched the fx... that way they won't fight.

If I use a button to change effects I can figure it out (because I can have the output only work when a modifier is on, and only turn on the modifier when the button is on.) But when I slide a fader to change fx I have no way to do that (that I know of.) Like what I want is to be able to set a modifier while I'm moving the fader, but then turn it back off when I stop moving the fader....
Nedra Fresneda
25.02.2011
Originally Posted by ThePattern
Padi, any word on those endless knobs? How did you do the fx knobs with no soft takeover?
Using the APC in regular (not dumb mode) they update by themselves if you assign the OUT to the same CC. On top of that, CC+8 is Outs are mapped to have multiple leds light up like they do in Ableton.

This does make the knobs move "slower" as IN/OUTs are fighting each other and it get's worse as the latency increases, but at 2-10ms it didn't bother me.

Try setting the latency to something like 30ms and see what I mean.
Julieta Cucinotta
25.02.2011		Padi, any word on those endless knobs? How did you do the fx knobs with no soft takeover?
Stephnie Godbole
25.02.2011
Originally Posted by padi_04
One last thing, it's the "Windows Friendly" version so the VU Meters were removed to avoid popping
Ah no problem. gonna run my stuff through mp3gain anyways and i usually have master out to -7
Nedra Fresneda
25.02.2011		One last thing, it's the "Windows Friendly" version so the VU Meters were removed to avoid popping
Stephnie Godbole
25.02.2011
Originally Posted by padi_04
It's the idea, but I sold the unit so can't map it myself.
well next month Ill have one so if needbe I can take your tsi and add it in when T2 is out
Nedra Fresneda
25.02.2011
Originally Posted by MuzicFreq
WOW NICE
Planning on making those 8 empty buttons below the deck be for the sample decks?
It's the idea, but I sold the unit so can't map it myself.
Stephnie Godbole
25.02.2011
Originally Posted by padi_04
Attached TSI & pic
WOW NICE
Planning on making those 8 empty buttons below the deck be for the sample decks?
Julieta Cucinotta
25.02.2011		Hey, I wanted to reverse engineer some of your features, but I can't seem to get the tsi file to show up in my mapper... Basically, I just wanted to know how you worked out the "no soft takeover" for fx. How do you set the knobs to the value when you switch effects?

Thanks!
Nedra Fresneda
31.01.2011		Attached TSI & pic
Isreal Roberto
17.01.2011		Been playing with it for a while, the VU meters don't work for me though...
Nedra Fresneda
09.11.2010
Originally Posted by robbiekurupt
howdy

i tried to import ur tsi but there is nothing on the file??? ive a few other mappings and they all load so it doesnt seem to be me or my laptop.

if u can have a look at it and let me know, id like to try urs out!!!
What version are you using? I just downloaded it and tested import on my mac and work pc. You need Traktor 1.2.4 or later.

The TSI file works
Gretchen Hargett
08.11.2010		howdy

i tried to import ur tsi but there is nothing on the file??? ive a few other mappings and they all load so it doesnt seem to be me or my laptop.

if u can have a look at it and let me know, id like to try urs out!!!

<< Back to Post and find Controller MappingsReply

Copyright 2012-2023
DJRANKINGS.ORG n.g.o.
Chuo-ku, Osaka, Japan

Created by Ajaxel CMS

Terms & Privacy