Traditional House
Progressive House
Tech House
Techno
Electro House
Trance
Electronica

United States
United Kingdom
Germany
Italy
France
Spain
Netherlands

DDM4000 traktor 2 mapping

Home :: Post and find Controller Mappings :: DDM4000 traktor 2 mappingReply

DDM4000 traktor 2 mapping Posted on: 15.05.2011 by Katerine Roethe hello all, I have an DDM4000 with audio2 and thus using it as a midi. with traktor pro everything was fine but now i've spend hours on a mapping it in traktor 2 for 2 play decks and 2 sample decks. And it's still not working properly(horribly).So i wondered of any of you fine lads has any ready made midi mapping for me. Thnx in advance
Lavenia Neild 14.07.2011	Originally Posted by djroketboy Yeah I had tried that, but from what I could see it only made the mapped LED's flash really fast back and fourth. Maybe I missed something so I will try it again. Right now I have it so note 34 will select Deck A and note 36 will select Deck B, the correlating LED will light up, so I know which deck is on. It does work, I just thought it would be nicer to use the crossfader to do it. Adding which deck is master, would just be icing on the cake, as right now I use the mouse (trackpad) to select the master deck. If a mapping isn't working correctly, the way I've come to test out what I'm doing is: - Export current settings - Delete current mappings - Add new mapping - Add just the commands I'm trying to test So after you've got your stuff backed up and create a new mapping, I would go in and add the two entries or Deck Focus and learn the left/right fader positions for each entry. Without anything else in the way, a simple command to switch decks when the fader sends is in the left or right position should work. I would worry about the LED's after all that is worked out.
Rosaura Dendrinos 14.07.2011	Originally Posted by Belmont! Yeah modifiers are tricky, I'm still getting used to them myself. But in this case if it's just Deck switching, you should be able to just make two entries for the Deck Focus command. Turn on learning and slide the fader all the way to the left, turn off learning, then set that to Deck A. Do the same for Deck B but move the fader all the way to the right. Is that the way you have it set up already? Yeah I had tried that, but from what I could see it only made the mapped LED's flash really fast back and fourth. Maybe I missed something so I will try it again. Right now I have it so note 34 will select Deck A and note 36 will select Deck B, the correlating LED will light up, so I know which deck is on. It does work, I just thought it would be nicer to use the crossfader to do it. Adding which deck is master, would just be icing on the cake, as right now I use the mouse (trackpad) to select the master deck.
Lavenia Neild 14.07.2011	Originally Posted by djroketboy I use Trackor Scratch Pro (v1) with 2 timecode vinyls. I am trying to get the crossfader to do focus select for A & B, also Master Select on both A & B. I have focus select working on notes 34 and 36 (manual select buttons) along with midi recieve working (turning on the LED's) for cc34 and cc 37. I believe I might have to use modifiers to get it to work, but not fully grasping them yet. Yeah modifiers are tricky, I'm still getting used to them myself. But in this case if it's just Deck switching, you should be able to just make two entries for the Deck Focus command. Turn on learning and slide the fader all the way to the left, turn off learning, then set that to Deck A. Do the same for Deck B but move the fader all the way to the right. Is that the way you have it set up already?
Rosaura Dendrinos 14.07.2011	Originally Posted by Belmont! Hey djroketboy, what is the piece of specific information you're looking for? I'm kind of new to mapping, but I'll do my best to help you find the answer. I use Trackor Scratch Pro (v1) with 2 timecode vinyls. I am trying to get the crossfader to do focus select for A & B, also Master Select on both A & B. I have focus select working on notes 34 and 36 (manual select buttons) along with midi recieve working (turning on the LED's) for cc34 and cc 37. I believe I might have to use modifiers to get it to work, but not fully grasping them yet.
Rosaura Dendrinos 14.07.2011	Originally Posted by bartboy The problem is you didn't look just because you Googled something doesn't mean you looked. People on this community have been more than nice enough to point you in the right direction but were not idiots were not gonna do the work for you. There are hundreds of posts on mapping and the DDM4000. So use this site's search button on RTFM. How do you know what I've done? You sitting here at my desk? In my search for what I am looking for, I found this useless thread. Along with the same old "search" reply that community s are so well known for. If there are "hundreds" of mappings for the DDM4000 why not fucking make a sticky post with ALL of them listed?? Its a know fact that vbulletins search sucks ass, and administrators put fucking stupid limits on searching. "People on this community have been more than nice enough to point you in the right direction but were not idiots were not gonna do the work for you." Excuse me? I just signed up today, not asking anyone to do work for me, i'm asking you to quit wasting my fucking time with gay ass "use the search button" replies. Just for the record, I have the Traktor Bible, and know how to map my DDM4000, I am looking for one specific piece of information that I can't get to work right. But fuck if I will ask on this site now.
Rosaura Dendrinos 15.07.2011	Originally Posted by photojojo If you never take the time to search you will never learn on your own. asking others to do everything for you will never get you any where. Buy the traktor Bible and empower yourself. It sounds like some of the things you might want to do are specific to you and not really thing others might want to do. https://traktorbible.com/shop/products.aspx Your theory is flawed. Aren't these community s for people to discuss and ask for help? I am so sick and tired searching Google and the first post (of what I am looking for) is "use search stupid". Just like this post. Its unproductive and a waste of time for everyone. If you don't want to moderate and let people ask questions on this site then just quit, or shut the community s down. If you don't want people asking questions then just shut down the community s, start blog, post your knowledge, turn off comments so no one can ask a question... then move on. I came from Google via searching, but since I can't find my answer; can't ask a question without being chastised, I might as well find a different site to ask a question on.
Leeanna Ayla 23.05.2011	Originally Posted by [email protected] @ xplode, nice you got an answer and thnx to the guy who gave it. but don't be to harsh sometimes i spend hours searching for an answer in these community s when it could be fixed by the efforts of 1 friendly guy taking a sec. it's apreciated! If you never take the time to search you will never learn on your own. asking others to do everything for you will never get you any where. Buy the traktor Bible and empower yourself. It sounds like some of the things you might want to do are specific to you and not really thing others might want to do. https://traktorbible.com/shop/products.aspx
Ralph Alderette 15.05.2011	Originally Posted by XplodeHD sorry i dont know how to map it i dont have it but im believeing i should buy one can you tell me if you can assign every knob fader etc for midi use and left 2 channels for normal use or it has some kind of presets couse i want to use only 2 channels analog and everything else like midi is this possible ? how is the quality of that mixer ? btw use http://www.traktorbible.com/en/t2_commandfinder.aspx command finer and map it yourself it shoud be easy use the SEARCH button on this site, you'll find plenty of info. short answer: everything except the CENTER FX SECTION and the GRAY GAIN KNOBS are MIDI. you can choose MIDI or Analog or Both at the same time. best mixer for the price
Ralph Alderette 15.05.2011	Originally Posted by [email protected] hello all, I have an DDM4000 with audio2 and thus using it as a midi. with traktor pro everything was fine but now i've spend hours on a mapping it in traktor 2 for 2 play decks and 2 sample decks. And it's still not working properly(horribly).So i wondered of any of you fine lads has any ready made midi mapping for me. Thnx in advance can you be more specific?... what are you trying to do?
Katerine Roethe 15.05.2011	hello all, I have an DDM4000 with audio2 and thus using it as a midi. with traktor pro everything was fine but now i've spend hours on a mapping it in traktor 2 for 2 play decks and 2 sample decks. And it's still not working properly(horribly).So i wondered of any of you fine lads has any ready made midi mapping for me. Thnx in advance
Lavenia Neild 14.07.2011	Originally Posted by djroketboy Yeah I had tried that, but from what I could see it only made the mapped LED's flash really fast back and fourth. Maybe I missed something so I will try it again. Right now I have it so note 34 will select Deck A and note 36 will select Deck B, the correlating LED will light up, so I know which deck is on. It does work, I just thought it would be nicer to use the crossfader to do it. Adding which deck is master, would just be icing on the cake, as right now I use the mouse (trackpad) to select the master deck. If a mapping isn't working correctly, the way I've come to test out what I'm doing is: - Export current settings - Delete current mappings - Add new mapping - Add just the commands I'm trying to test So after you've got your stuff backed up and create a new mapping, I would go in and add the two entries or Deck Focus and learn the left/right fader positions for each entry. Without anything else in the way, a simple command to switch decks when the fader sends is in the left or right position should work. I would worry about the LED's after all that is worked out.
Ralph Alderette 14.07.2011	I dont have my DDM4000 anymore, but do the lights flicker back and forth ONLY when you move the fader? If so, it might be the settings on the actual MIDI button commands. For example, Instead of "HOLD" set to "Direct". In terms of mapping it out to the fader, yea you're mapping it right. Both commands go to the same fader.
Rosaura Dendrinos 14.07.2011	Originally Posted by Belmont! Yeah modifiers are tricky, I'm still getting used to them myself. But in this case if it's just Deck switching, you should be able to just make two entries for the Deck Focus command. Turn on learning and slide the fader all the way to the left, turn off learning, then set that to Deck A. Do the same for Deck B but move the fader all the way to the right. Is that the way you have it set up already? Yeah I had tried that, but from what I could see it only made the mapped LED's flash really fast back and fourth. Maybe I missed something so I will try it again. Right now I have it so note 34 will select Deck A and note 36 will select Deck B, the correlating LED will light up, so I know which deck is on. It does work, I just thought it would be nicer to use the crossfader to do it. Adding which deck is master, would just be icing on the cake, as right now I use the mouse (trackpad) to select the master deck.
Lavenia Neild 14.07.2011	Originally Posted by djroketboy I use Trackor Scratch Pro (v1) with 2 timecode vinyls. I am trying to get the crossfader to do focus select for A & B, also Master Select on both A & B. I have focus select working on notes 34 and 36 (manual select buttons) along with midi recieve working (turning on the LED's) for cc34 and cc 37. I believe I might have to use modifiers to get it to work, but not fully grasping them yet. Yeah modifiers are tricky, I'm still getting used to them myself. But in this case if it's just Deck switching, you should be able to just make two entries for the Deck Focus command. Turn on learning and slide the fader all the way to the left, turn off learning, then set that to Deck A. Do the same for Deck B but move the fader all the way to the right. Is that the way you have it set up already?
Rosaura Dendrinos 14.07.2011	Originally Posted by Belmont! Hey djroketboy, what is the piece of specific information you're looking for? I'm kind of new to mapping, but I'll do my best to help you find the answer. I use Trackor Scratch Pro (v1) with 2 timecode vinyls. I am trying to get the crossfader to do focus select for A & B, also Master Select on both A & B. I have focus select working on notes 34 and 36 (manual select buttons) along with midi recieve working (turning on the LED's) for cc34 and cc 37. I believe I might have to use modifiers to get it to work, but not fully grasping them yet.
Lavenia Neild 14.07.2011	Hey djroketboy, what is the piece of specific information you're looking for? I'm kind of new to mapping, but I'll do my best to help you find the answer.
Rosaura Dendrinos 14.07.2011	Originally Posted by bartboy The problem is you didn't look just because you Googled something doesn't mean you looked. People on this community have been more than nice enough to point you in the right direction but were not idiots were not gonna do the work for you. There are hundreds of posts on mapping and the DDM4000. So use this site's search button on RTFM. How do you know what I've done? You sitting here at my desk? In my search for what I am looking for, I found this useless thread. Along with the same old "search" reply that community s are so well known for. If there are "hundreds" of mappings for the DDM4000 why not fucking make a sticky post with ALL of them listed?? Its a know fact that vbulletins search sucks ass, and administrators put fucking stupid limits on searching. "People on this community have been more than nice enough to point you in the right direction but were not idiots were not gonna do the work for you." Excuse me? I just signed up today, not asking anyone to do work for me, i'm asking you to quit wasting my fucking time with gay ass "use the search button" replies. Just for the record, I have the Traktor Bible, and know how to map my DDM4000, I am looking for one specific piece of information that I can't get to work right. But fuck if I will ask on this site now.
Lavenia Neild 14.07.2011	Oh cool, I have a DDM4000, it hadn't even occurred to me to use it as a controller. Hmmmm... possibilities.
Dana Ordinario 14.07.2011	The problem is you didn't look just because you Googled something doesn't mean you looked. People on this community have been more than nice enough to point you in the right direction but were not idiots were not gonna do the work for you. There are hundreds of posts on mapping and the DDM4000. So use this site's search button on RTFM.
Rosaura Dendrinos 15.07.2011	Originally Posted by photojojo If you never take the time to search you will never learn on your own. asking others to do everything for you will never get you any where. Buy the traktor Bible and empower yourself. It sounds like some of the things you might want to do are specific to you and not really thing others might want to do. https://traktorbible.com/shop/products.aspx Your theory is flawed. Aren't these community s for people to discuss and ask for help? I am so sick and tired searching Google and the first post (of what I am looking for) is "use search stupid". Just like this post. Its unproductive and a waste of time for everyone. If you don't want to moderate and let people ask questions on this site then just quit, or shut the community s down. If you don't want people asking questions then just shut down the community s, start blog, post your knowledge, turn off comments so no one can ask a question... then move on. I came from Google via searching, but since I can't find my answer; can't ask a question without being chastised, I might as well find a different site to ask a question on.
Leeanna Ayla 23.05.2011	Originally Posted by [email protected] @ xplode, nice you got an answer and thnx to the guy who gave it. but don't be to harsh sometimes i spend hours searching for an answer in these community s when it could be fixed by the efforts of 1 friendly guy taking a sec. it's apreciated! If you never take the time to search you will never learn on your own. asking others to do everything for you will never get you any where. Buy the traktor Bible and empower yourself. It sounds like some of the things you might want to do are specific to you and not really thing others might want to do. https://traktorbible.com/shop/products.aspx
Ralph Alderette 23.05.2011	sry, i get grumpy when I'm hungry lolz. i just enforce the whole search button thing a lot. sry ^O^ you wanna use the ddm just for sample decks?? thats crazy talk! well.. you could borrow inspiration from the mappings for the new Midifighter Pro's: 3 knobs for 3 sample slot filters, and then use map the Fader for an overall sample deck volume fader?? do that for each extra channel you have and ta-dum!!... 2 sample decks, plus to main decks!
Dana Ordinario 22.05.2011	http://traktorbible.com/freaks/mappingone.aspx?id=32 Those mappings are specific for the DDM4000. I'm pretty sure that all mappings are upward compatible with future releases just not the other way around I believe I could be wrong thou. Let me know if that works also Google is your friend, don't rely on everyone to do the work for you you won't get very far.
Katerine Roethe 22.05.2011	and im gonna look at the commandfinder right now, not a clue what it is
Katerine Roethe 22.05.2011	@ xplode, nice you got an answer and thnx to the guy who gave it. but don't be to harsh sometimes i spend hours searching for an answer in these community s when it could be fixed by the efforts of 1 friendly guy taking a sec. it's apreciated! and further for my question: I have mapped it myself for a large part right now but i still have the feeling i've missed some things and i tought if someone with a lot more traktor experience already made some mappings i could work from there. but to be more specific im trying to get like 2 decks just for playing the mp3's wich is working fine, but i just cant seem to make a clever mapping for controlling the sample decks with the two ''rows'' of knobs and faders (or are they called channels aswell?) i have left for sample decks. ideally i want to be able to control as much slots induvidually(playing/paus with a button and the volume) with what the buttons i have left. It's really hard for a non-techie guy like me to picture how it should be. frankly i just don't know how to get te mapping optimized. Looking forward to your reply, and my apoliegies for not being able to be very concrete about it. ps. also I want to start a co-op with a co ''dj'' to see if its possible with two or 3 mixers to only play by sample decks (he has xone 3d and 1 d i believe) with audio 8 and everything. wich brings me to the next mapping evening mare how would my ddm4000 be mapped solely for sampledecks. but first things first.
Ralph Alderette 15.05.2011	Originally Posted by XplodeHD sorry i dont know how to map it i dont have it but im believeing i should buy one can you tell me if you can assign every knob fader etc for midi use and left 2 channels for normal use or it has some kind of presets couse i want to use only 2 channels analog and everything else like midi is this possible ? how is the quality of that mixer ? btw use http://www.traktorbible.com/en/t2_commandfinder.aspx command finer and map it yourself it shoud be easy use the SEARCH button on this site, you'll find plenty of info. short answer: everything except the CENTER FX SECTION and the GRAY GAIN KNOBS are MIDI. you can choose MIDI or Analog or Both at the same time. best mixer for the price
Ralph Alderette 15.05.2011	Originally Posted by [email protected] hello all, I have an DDM4000 with audio2 and thus using it as a midi. with traktor pro everything was fine but now i've spend hours on a mapping it in traktor 2 for 2 play decks and 2 sample decks. And it's still not working properly(horribly).So i wondered of any of you fine lads has any ready made midi mapping for me. Thnx in advance can you be more specific?... what are you trying to do?
Hyman Bordenkircher 15.05.2011	sorry i dont know how to map it i dont have it but im believeing i should buy one can you tell me if you can assign every knob fader etc for midi use and left 2 channels for normal use or it has some kind of presets couse i want to use only 2 channels analog and everything else like midi is this possible ? how is the quality of that mixer ? btw use http://www.traktorbible.com/en/t2_commandfinder.aspx command finer and map it yourself it shoud be easy

<< Back to Post and find Controller Mappings Reply

Copyright 2012-2023 DJRANKINGS.ORG n.g.o. Chuo-ku, Osaka, Japan	Created by Ajaxel CMS
Terms & Privacy

The best DJ in Mexico is:

DDM4000 traktor 2 mapping