TouchOSC (Iphone/Ipod) Mart's Mix Layout (TP2)
TouchOSC (Iphone/Ipod) Mart's Mix Layout (TP2) Posted on: 08.02.2012 by Asha Kravetz Several Hours of work and some crafty midi mapping later, a full on mapping for TP2 comes out.First Page Screen Shot 2012-02-08 at 9.55.15 AM | Flickr - Photo Sharing! Basic Mixer- EQ- Low= Red Mid= Orange. High=yellow. Two Blue Knobs= Filters. There's an LED mapped out in the middle responding to when then filter is on or not Purple faders= Post Fader VU meters (It's really cool to see how they respond to the track volume ) Moving on down- The two large red and green faders are volume faders. This is the introduction of the color coding system (Green for Deck A, Red for B) The top button to the right of the fader is the cue monitor button Down from that in the grey is sync Below that is cue (orange) And finally at the bottom is play The next two pages are Jogwheels and Pitch faders for each deck. Turn the device so that the circle I is at the top and use the fader just like on a controller. Note: Jogs are pitch bend only. Everything is color coded- left deck green, right deck red Screen Shot 2012-02-08 at 9.55.40 AM | Flickr - Photo Sharing! The page after that is the loop and browser section The encoders on the right select auto loop size (color coded for each deck) The large button immediately to the left of the encoders is the loop on/off (color coded) Even more to the left, two small buttons are loop in (on top) loop out ( bottom) Screen Shot 2012-02-08 at 9.55.52 AM | Flickr - Photo Sharing! The orange encoder serves as a browser knob- allowing you to move up and down your tracks in a folder, and the two buttons to the side (color coded) allow you to load to each deck The last page is the FX page. Controls are color coded. Bank on top is FX 2 routed to deck B (Red) Bank on the bottom is FX unit 1 and color coded to deck A. The knob to the top left in the red, and the only green knob in its row are Dry/wet controls Screen Shot 2012-02-08 at 9.56.06 AM | Flickr - Photo Sharing! The three buttons in each bank turn each effect on and off respectively. The three knobs in a row control the 'amount' of effects 1-3. In the middle of each of those knobs is an LED that will illuminate once you hit the effect on button to serve as a visual indicator. As usual, hit the big import button and import the .TSI into traktor, select every one of the options. You must sync the layout to your device using the TouchOSC editor. This is configured with TouchOSC V1.8 and uses the free touchosc bridge application. Enjoy! Contact me before you attempt to share the mapping elsewhere, and NEVER attempt to sell it. this mapping is always free. | |
| Asha Kravetz 08.02.2012 | Several Hours of work and some crafty midi mapping later, a full on mapping for TP2 comes out. First Page Screen Shot 2012-02-08 at 9.55.15 AM | Flickr - Photo Sharing! Basic Mixer- EQ- Low= Red Mid= Orange. High=yellow. Two Blue Knobs= Filters. There's an LED mapped out in the middle responding to when then filter is on or not Purple faders= Post Fader VU meters (It's really cool to see how they respond to the track volume ) Moving on down- The two large red and green faders are volume faders. This is the introduction of the color coding system (Green for Deck A, Red for B) The top button to the right of the fader is the cue monitor button Down from that in the grey is sync Below that is cue (orange) And finally at the bottom is play The next two pages are Jogwheels and Pitch faders for each deck. Turn the device so that the circle I is at the top and use the fader just like on a controller. Note: Jogs are pitch bend only. Everything is color coded- left deck green, right deck red Screen Shot 2012-02-08 at 9.55.40 AM | Flickr - Photo Sharing! The page after that is the loop and browser section The encoders on the right select auto loop size (color coded for each deck) The large button immediately to the left of the encoders is the loop on/off (color coded) Even more to the left, two small buttons are loop in (on top) loop out ( bottom) Screen Shot 2012-02-08 at 9.55.52 AM | Flickr - Photo Sharing! The orange encoder serves as a browser knob- allowing you to move up and down your tracks in a folder, and the two buttons to the side (color coded) allow you to load to each deck The last page is the FX page. Controls are color coded. Bank on top is FX 2 routed to deck B (Red) Bank on the bottom is FX unit 1 and color coded to deck A. The knob to the top left in the red, and the only green knob in its row are Dry/wet controls Screen Shot 2012-02-08 at 9.56.06 AM | Flickr - Photo Sharing! The three buttons in each bank turn each effect on and off respectively. The three knobs in a row control the 'amount' of effects 1-3. In the middle of each of those knobs is an LED that will illuminate once you hit the effect on button to serve as a visual indicator. As usual, hit the big import button and import the .TSI into traktor, select every one of the options. You must sync the layout to your device using the TouchOSC editor. This is configured with TouchOSC V1.8 and uses the free touchosc bridge application. Enjoy! Contact me before you attempt to share the mapping elsewhere, and NEVER attempt to sell it. this mapping is always free. |
| Eulah Tamkin 18.09.2012 | Where is the link for download? Did I miss it? |
<< Back to Post and find Controller MappingsReply