4 Banks mapping
4 Banks mapping Posted on: 18.07.2012 by Kellie Myrum This is setup for 4 buttons and it can go up to 7 values /buttons in one modifier. This means a lot more potential to your controller when it come to some more complex mappings. Try it out!Add in modifier #1 Type of controller - Button Interaction mode - Direct Set to value - 1 Add out modifier #1 Controller range - 1 to 1 Add in modifier #1 Type of controller - Button Interaction mode - Direct Set to value - 2 Controller range - 2 to 2 Add in modifier #1 Type of controller - Button Interaction mode - Direct Set to value - 3 Controller range - 3 to 3 Add in modifier #1 Type of controller - Button Interaction mode - Direct Set to value - 4 Controller range - 4 to 4 4 bank mod.tsi | |
| Elton Rackley 20.06.2013 |
Originally Posted by 0Notice
Untitled 1.pdf I know it doesnt make sense to have the modifier on the "Loop Active ON" switch but it seems to work better (could just be my controller). I am running TSP 2.6 with a Novation launchpad, External mixer and a remote zero for FX. My LED Output range is actually 10-19 (red - orange) but the default 0-127 (ON/OFF) should be fine or change it as you need it. I had this running with 4 decks a while back. I just might set that up again. Invert and Blend are unchecked for all parameters. Good luck. |
| Kellie Myrum 21.11.2012 |
Originally Posted by 0Notice
|
| Valeri Millstein 21.11.2012 |
Originally Posted by Stewe
|
| Valeri Millstein 21.11.2012 |
Originally Posted by Stewe
|
| Kellie Myrum 18.07.2012 | This is setup for 4 buttons and it can go up to 7 values /buttons in one modifier. This means a lot more potential to your controller when it come to some more complex mappings. Try it out! Add in modifier #1 Type of controller - Button Interaction mode - Direct Set to value - 1 Add out modifier #1 Controller range - 1 to 1 Add in modifier #1 Type of controller - Button Interaction mode - Direct Set to value - 2 Controller range - 2 to 2 Add in modifier #1 Type of controller - Button Interaction mode - Direct Set to value - 3 Controller range - 3 to 3 Add in modifier #1 Type of controller - Button Interaction mode - Direct Set to value - 4 Controller range - 4 to 4 4 bank mod.tsi |
| Elton Rackley 20.06.2013 |
Originally Posted by 0Notice
Untitled 1.pdf I know it doesnt make sense to have the modifier on the "Loop Active ON" switch but it seems to work better (could just be my controller). I am running TSP 2.6 with a Novation launchpad, External mixer and a remote zero for FX. My LED Output range is actually 10-19 (red - orange) but the default 0-127 (ON/OFF) should be fine or change it as you need it. I had this running with 4 decks a while back. I just might set that up again. Invert and Blend are unchecked for all parameters. Good luck. |
| Kellie Myrum 21.11.2012 | That should be easy as assigning modifier condition 'Is in Active loop' to Loop Size Selector LED outputs. Add out > Deck Common > Loop > Loop Size Selector modifier condition - Is in Active loop (will lite only if loop engaged) controller range - 0-0 (example for /32) This is off topic here btw. |
| Valeri Millstein 21.11.2012 | Still cant get it to work could you give me the full run through, Add in > (something) > Then the modifiers. This is driving me bloody insane. Thanks. |
| Kellie Myrum 21.11.2012 |
Originally Posted by 0Notice
|
| Valeri Millstein 21.11.2012 |
Originally Posted by Stewe
|
| Kellie Myrum 21.11.2012 | Loop size / Controller ange /32 = 0 /16 = 1 /8 = 2 /4 = 3 /2 = 4 1 = 5 2 = 6 4 = 7 8 = 8 16 = 9 32 = 10 |
| Valeri Millstein 21.11.2012 |
Originally Posted by Stewe
|
| Kellie Myrum 22.11.2012 | You can follow order in controller range from my original post. |
| Valeri Millstein 22.11.2012 | Still can't get the bloody thing to work I have my 8 Buttons mapped to specify values and to turn on looping. Now I have each of those buttons mapped to change the modifier directly 0-7. Any help on mapping the LED output. Please. |
| Kellie Myrum 26.07.2012 | Here is one short demo video: |
| Kellie Myrum 25.07.2012 | I'm glad that helped. |
| Arturo Harbuck 25.07.2012 | ok - than i've done correctly. thx again! |
| Kellie Myrum 25.07.2012 | No, I meant of beat phase monitor there also. Until Tractor can offer some kind of optional state blink command we must satisfy with what we got |
| Arturo Harbuck 25.07.2012 | ok, thx for the advice. you mean the normal phase instead of the beatphase? had hoped that there is a better solution. but somehow i get used to map x commands for one function. |
| Kellie Myrum 25.07.2012 | You should map all four deck's phase monitors to every each four buttons for that scenario. |
| Arturo Harbuck 25.07.2012 | oh i forgot - the xone k2. at the moment i mapped four beatphase monitors per button (A,B,C,D) since at least one deck is running - but i believe its not a clean solution. |
| Kellie Myrum 25.07.2012 | Hey iona, what controller do you map to traktor? Sure, it is possible. |
| Arturo Harbuck 25.07.2012 | is it possible to map them blinking? i had the idea to map a beatphase monitor out to each button, but since its connected to a specified deck or focus it won't work... |
<< Back to Post and find Controller MappingsReply