Calvin Harris
and Dillon Francis
worked there... no way!
| Howto LED loop active? So, tried searching the community
s with not much luck. I'm trying to map my launchpad LEDs to go bright when a loop is active (as in JWILLs mapping), but just can't do it! I don't get it, I set the LED up the same way (LED Output for Loop Active, Controller Range 0/1, Midi Range 85/127, no invert, no blend) but all the LED will do is go pfft once I press it, even though the loop is active I have no LED lights.. Why is this? :-\ | Queen Sichel
19.11.2011 |
Originally Posted by zestoi
just tried that and seems to work fine. traktor outputs this midi when i press loop to enable and again to disable:
Code:
* [traktor ] 90 18 7f [traktor] type=note-on name=C0 value=127
* [traktor ] 90 18 55 [traktor] type=note-on name=C0 value=85
i piped that midi direct to my launchpad and a pad went bright then dimmer. i did select deck A in the controller manager for it. check that and/or you have the correct launchpad note entered in traktor, which u can't use 'learn' for ofc.
edit: ignore that i used "C0" that was just something not already used by my midimasher/traktor devices file - you need the actual launchpad note or cc ofc.
Bah. It works. I hade two outs for Loop Active conflicting. Can't believe I didn't check that before posting here... Thanks for trying it out so I didn't have to tear my hear anymore though... | Chasidy Heckenbach
18.11.2011 |
Originally Posted by koffa
So, tried searching the community
s with not much luck. I'm trying to map my launchpad LEDs to go bright when a loop is active (as in JWILLs mapping), but just can't do it! I don't get it, I set the LED up the same way (LED Output for Loop Active, Controller Range 0/1, Midi Range 85/127, no invert, no blend) but all the LED will do is go pfft once I press it, even though the loop is active I have no LED lights.. Why is this? :-\
just tried that and seems to work fine. traktor outputs this midi when i press loop to enable and again to disable:
Code:
* [traktor ] 90 18 7f [traktor] type=note-on name=C0 value=127
* [traktor ] 90 18 55 [traktor] type=note-on name=C0 value=85
i piped that midi direct to my launchpad and a pad went bright then dimmer. i did select deck A in the controller manager for it. check that and/or you have the correct launchpad note entered in traktor, which u can't use 'learn' for ofc.
edit: ignore that i used "C0" that was just something not already used by my midimasher/traktor devices file - you need the actual launchpad note or cc ofc. | Queen Sichel
18.11.2011 | So, tried searching the community
s with not much luck. I'm trying to map my launchpad LEDs to go bright when a loop is active (as in JWILLs mapping), but just can't do it! I don't get it, I set the LED up the same way (LED Output for Loop Active, Controller Range 0/1, Midi Range 85/127, no invert, no blend) but all the LED will do is go pfft once I press it, even though the loop is active I have no LED lights.. Why is this? :-\ | Queen Sichel
19.11.2011 |
Originally Posted by zestoi
just tried that and seems to work fine. traktor outputs this midi when i press loop to enable and again to disable:
Code:
* [traktor ] 90 18 7f [traktor] type=note-on name=C0 value=127
* [traktor ] 90 18 55 [traktor] type=note-on name=C0 value=85
i piped that midi direct to my launchpad and a pad went bright then dimmer. i did select deck A in the controller manager for it. check that and/or you have the correct launchpad note entered in traktor, which u can't use 'learn' for ofc.
edit: ignore that i used "C0" that was just something not already used by my midimasher/traktor devices file - you need the actual launchpad note or cc ofc.
Bah. It works. I hade two outs for Loop Active conflicting. Can't believe I didn't check that before posting here... Thanks for trying it out so I didn't have to tear my hear anymore though... | Chasidy Heckenbach
18.11.2011 |
Originally Posted by koffa
So, tried searching the community
s with not much luck. I'm trying to map my launchpad LEDs to go bright when a loop is active (as in JWILLs mapping), but just can't do it! I don't get it, I set the LED up the same way (LED Output for Loop Active, Controller Range 0/1, Midi Range 85/127, no invert, no blend) but all the LED will do is go pfft once I press it, even though the loop is active I have no LED lights.. Why is this? :-\
just tried that and seems to work fine. traktor outputs this midi when i press loop to enable and again to disable:
Code:
* [traktor ] 90 18 7f [traktor] type=note-on name=C0 value=127
* [traktor ] 90 18 55 [traktor] type=note-on name=C0 value=85
i piped that midi direct to my launchpad and a pad went bright then dimmer. i did select deck A in the controller manager for it. check that and/or you have the correct launchpad note entered in traktor, which u can't use 'learn' for ofc.
edit: ignore that i used "C0" that was just something not already used by my midimasher/traktor devices file - you need the actual launchpad note or cc ofc. |
|
