Can I map crossfader curve?

Home :: Post and find Controller Mappings :: Can I map crossfader curve?Reply
Can I map crossfader curve?
Posted on: 01.12.2011 by Percy Keehan
I have only have Traktor Pro 1 and I don't really believe I am going to upgrade yet, but I want to know. In Traktor Pro 2, can you map a knob to crossfader curve?
Percy Keehan
02.12.2011
Originally Posted by VanGogo
Ok I googled the TPro 1 manual and it wasn't in there, but it was in an addendum to the manual, and it's right where I said it was.
dont worry u already answered my question. i wanted to know if it was in pro 2 for when i upgrade
Percy Keehan
01.12.2011
Originally Posted by VanGogo
Ok that was so easy you must not have even looked for it.
In controller manager where you do midi mapping click add in, go down to mixer, it says X-fader curve.
i dont have traktor pro 2..... i have traktor pro 1
Percy Keehan
01.12.2011
Originally Posted by VanGogo
You can map the smooth to sharp cut action of the cross fader that you adjust in preferences.
yeah thats what i meant? so i can map that to knobs and stuff?
Percy Keehan
01.12.2011		I have only have Traktor Pro 1 and I don't really believe I am going to upgrade yet, but I want to know. In Traktor Pro 2, can you map a knob to crossfader curve?
Lilliana Perris
03.12.2011		I managed to get my XFader on my APC40 to be pretty damn sharp.

I set the XFader midi command to Fader or Knob and set it from direct to Relative.

Then you will give you the sensitivity and velocity section. Play with that.

I have got it set that when i tap the fader like I want to open the fader while holding it closed, it jumps to half way.
So that equates to the cut being sharp.

Its not a 100% solution, but helped me out a lot with using the APC Xfader to scratch.
Percy Keehan
02.12.2011
Originally Posted by VanGogo
Ok I googled the TPro 1 manual and it wasn't in there, but it was in an addendum to the manual, and it's right where I said it was.
dont worry u already answered my question. i wanted to know if it was in pro 2 for when i upgrade
Charline Dye
02.12.2011		Ok I googled the TPro 1 manual and it wasn't in there, but it was in an addendum to the manual, and it's right where I said it was.
Charline Dye
02.12.2011		I had this mapped in TPro 1 also so I'm sure it's there somewhere. What does it say in the mixer section of the add in? If its not there just go through the different sections till you locate it. The manual will probably mention it somewhere also.
Percy Keehan
01.12.2011
Originally Posted by VanGogo
Ok that was so easy you must not have even looked for it.
In controller manager where you do midi mapping click add in, go down to mixer, it says X-fader curve.
i dont have traktor pro 2..... i have traktor pro 1
Charline Dye
01.12.2011		Ok that was so easy you must not have even looked for it.
In controller manager where you do midi mapping click add in, go down to mixer, it says X-fader curve.
Charline Dye
01.12.2011		I'll look later toevening when I get home. Should be in midi command list some where. I use a midi keyboard for an added controller, and have it mapped to the modulator wheel, but a knob or fader will do nicely.
Percy Keehan
01.12.2011
Originally Posted by VanGogo
You can map the smooth to sharp cut action of the cross fader that you adjust in preferences.
yeah thats what i meant? so i can map that to knobs and stuff?
Charline Dye
01.12.2011		You can map the smooth to sharp cut action of the cross fader that you adjust in preferences.
Ada Matzkin
01.12.2011		i dont believe so, i wish there was tho.

<< Back to Post and find Controller MappingsReply

Copyright 2012-2023
DJRANKINGS.ORG n.g.o.
Chuo-ku, Osaka, Japan

Created by Ajaxel CMS

Terms & Privacy