Reply to Turn 2 LPD8 into a MidiFighter (leds working)

It's done, MidiFighter on two LPD'8 with working LED's.
All Pads are set Momentarly. No cheap Toggle-On Trick.

Cause i love the MidiFighter & the Mapping, i decided to convert it to my old two LPD8.
When you add following Commands to your MidiFighter-Mapping, you could use it, like the MidiFighter.


Well the case is that on the LPD8 Led Out won't work properly, so i never made a "serious" mapping. I decidet to use the LPD8's for FX1-4, and to monitor events. Like Phase_Monitor; BeatPhase_Monitor; MasterClip, Pan; DeckFocusSelect and so on.
But now i figured out how to Trick the LPD8 out, and make LED OUT work, without BomeMIdi, MidiJoke and so on (also not properly but way more useful than now)


How it's done?
Instead of using the same OUT-Command like IN-Command, i use a Trick. You need an constant Signal (per example the "Beat Phase Monitor".
An example on the Play Button (cause this Trick works only proper if focused Deck is played)


EXAMPLE
D#3 (Play)
Add IN => Transport => Play/Pause (in our Example this is Channel3_D#3)

now don't add the same Command for OUT
(don't Add OUT => Transport => Play/Pause)

use this
Add OUT => Output => Beat Phase Monitor
Deselect Invert & Blend
Controller Range => min = -0.50 max = 0.50 (so it won't blink, it stays)
very important = Modifier Conditions => Play/Pause => Device Target == 1
exactly like on this image



Now what happen's is, when you hit Play, Beat Phase Monitor will send "Signals" as long the Deck is played. (it don't will blink, just blend with the right settings)
So you can change DeckFocus, and it will Update the State of the LED.








G#2 (Sampler/Record Button)
Other Example (Modifiers/Shift G#2)
In the Midifighter-Mapping is a Record/Sampler Button. Which is tricky, cause when you hit it, it goes in a SamplerMode, and when you will press in this SamplerMode, Shift + Record, you'll get in the Beatjuggle-Mode.
So how you can make that you'll know in which mode you are.

Well, it works like this. SamplerMode
Add OUT => Global => Beat Phase Monitor
Modifiers Conditions1 => M3 = 1
Modifiers Conditions2 => M2 = 0
Controller Range => min = 0.5 max = 0.5
Select INVERT



Now if you press the SamplerButton, it will blend if you're in this Mode. Now if you press Shift + SamplerButton. It will begin blinking when you add the next Command in your mapping.

Add OUT => Global => Beat Phase Monitor
Modifiers Conditions1 => M3 = 1
Modifiers Conditions2 => M2 = 3
Controller Range => min = 0 max = 0.5
Select INVERT

So now you can see in which Mode you are.








C#3 (Sync)
Sync Out won't work properly, so i added something similar.
Done it with
Add OUT => Output => Phase Monitor
(the PhaseMonitor is the thing that shows you if you're synced)
Cause i don't want the Phase Monitor like it is, i make some settings

Controller Range => min = -0.005 max = 0.005

So the sync button only will blend if the Phase is in Sync (but sync must NOT be activated)
(if you press Sync, the Led will go Off, but after 3-4 seconds it will come back , cause Sync Out is also mapped on this)








D3 (Cue)
Cause i use the "Deckalized Focus A&B" but want also be able to load next Tracks (in stopped Decks only) using Shift + Cue
i add following
Add IN => Load => Load Next
Modifiers Condition1 => M7 =1
Modifiers Condition2 => Play/Pause => Device Target ==1

(now if you want you can make D3 Led monitors if other deck is in play )











Turn two LPD8 into a MidiFighter HOW TO

1.) Download LPD8 Editor Mac / Windows (How it works)

2.) Download these Config Files for LPD8 Editor (attention these files configure only scene/preset 4, all other Scenes will not affected)
it contains "LPD8 Top" and "LPD8 Bottom"
FILES

Plug just ONE LPD8 in, start LPD8-Editor and set up (TOP)
Commit Upload "LPD8 TOP"

Plug LPD8 out, and plug in the other.
Commit Upload "LPD8 Bottom"

Now you're LPD8 got the same MidiChannel (CH3) as the Midifighter and also sends the same Note's.


Now download you're favorite Mapping for the MidiFighter and add all the Commands from here.

ATTENTION
Be sure no other Controller sends on MidiChannel3
Be sure you set the MIDI IN and MIDI OUT to ALL PORTS in Traktor



If you don't wanna modify the MidiFighter-Mapping, you could use this.
Its a modified "Deckalized Focus A&B Mapping for the LPD8"




i recently don't add any other functions (knobs or CC) just the MidiFighter as it is