Hotcue LEDS won't go out
Hotcue LEDS won't go out Posted on: 01.09.2012 by Aleen Kennelley Hi guys,If been searching now for hours on this and I just can't figure it out (since they changed from Hotcue State). I map my Hot cues and LED's and they work fine. When I store a hot cue, the LED turns on, all fine there. The problem is when I delete the hot cue the LED won't turn off Anyone can tell me what exactly I've got to do to get this fixed. I must miss something but I can't seem to figure out what. Thx for your help. Yoeri. | |
| Kellie Myrum 03.09.2012 |
Originally Posted by Perdut
|
| Aleen Kennelley 02.09.2012 | Hi Stewe, That's exactly what I did but it doesn't work, that's what drives me nuts. Here's one of the versions I've tried. Can you see what I've done wrong ? Schermafbeelding 2012-09-02 om 13.47.23.png |
| Aleen Kennelley 01.09.2012 | Hi guys, If been searching now for hours on this and I just can't figure it out (since they changed from Hotcue State). I map my Hot cues and LED's and they work fine. When I store a hot cue, the LED turns on, all fine there. The problem is when I delete the hot cue the LED won't turn off Anyone can tell me what exactly I've got to do to get this fixed. I must miss something but I can't seem to figure out what. Thx for your help. Yoeri. |
| Kellie Myrum 04.09.2012 | Try to delete Play button LED output and map it again. No blend checked. |
| Aleen Kennelley 04.09.2012 | Oh yeah... it functions correctly, it's just those bloody LED's or feedback. I see that I haven't mentioned it before but I'm creating a whole mapping for the iPad (TouchOSC) to my likes. |
| Kellie Myrum 03.09.2012 |
Originally Posted by Perdut
|
| Aleen Kennelley 03.09.2012 | Works.... !!!!! My initial settings were correct it was just the settings in the ranges like Stewe said. Thx guys. PS. You know... this is now finally working and WITHOUT changing other parameters, for some reason now, the feedback to the PLAY buttons don't work correct anymore. I press 'play' and the light won't turn on immediatly. If I press the programmed 'status' button it pops up straight away. If I Pause/Stop the track it just goes out as supposed to. |
| Kellie Myrum 04.09.2012 | My hotcues are assigned to buttons which doesn't support LED output so I didn't actually mess with hotcue outputs in 2.5 but I knew it was renamed. So i tried to troubleshoot it and see what is the problem there. I added only one output for "hotcue # tupe" and it worked. Thing was with controller range, I started from 0-0 and it lite properly. |
| Kecia Wnukowski 03.09.2012 | try adding a sending monitor state command twice, one normal, one set to invert. |
| Kellie Myrum 03.09.2012 | Did you set range for hotcue type? Controller range 0-0 Midi range 0-127 No blend checked. |
| Kellie Myrum 03.09.2012 | Also make sure to set midi In/Out port to your controller. |
| Leeanna Ayla 03.09.2012 | Try deleting the commands and mapping them again. |
| Aleen Kennelley 03.09.2012 | Done that... nope. Not working. Arrrgghh..... I've seen it working so it must be something that I'm doing wrong. |
| Kellie Myrum 02.09.2012 | Hm.. Try adding M1=0 as condition for LED type same as you did for store hotcues. |
| Aleen Kennelley 02.09.2012 | Hi Stewe, That's exactly what I did but it doesn't work, that's what drives me nuts. Here's one of the versions I've tried. Can you see what I've done wrong ? Schermafbeelding 2012-09-02 om 13.47.23.png |
| Kellie Myrum 02.09.2012 | It's changed like many commands in 2.5 Add out > Track deck > Cue > Hotcue # type |
<< Back to Post and find Controller MappingsReply