Reply to The Spectra > Instant Grats Isolate FX

The Spectra > Instant Grats Isolate FX
This mapping doesn't contain just the popular Gratify effects bat also an advanced performance tool to get even more creative.

Download from DJTT mappings page: https://maps.djranking s.com/mappings/1455
-Unzip the file and import your "mfs" file in the MF utillity softwate and your "TSI" file in to Traktor.

Main features:

*INSTANT Gratification effects
*FX Unit focus selector
*Isolator FX for decks A and B (side buttons #1)
*EQ adjust for decks C and D (side buttons #2)

This mapping for Spectra has one main page where you would expect your Grats to be located at and other two sub-pages that can be reached and activated via side buttons.

Short demo:


Home page:



These are exact IG effects that everybody are used to but a little modified to fit this mapping. In order to utilize an Isolator in this TSI I needed to remove two supercombos because Traktor only support up to two modifier condition slots. Other thing which was modified is 'FX save' function that was mapped to your deck select buttons - now you can achieve the same result by holding any of effects > hitting side buttons (sub-page) and releasing the effect button. I've also added 'Kill FX' to your side buttons #3 so you can quickly got out of hold FX mode.

You can notice that left side buttons play on hold and right buttons are in toggling mode, thought it would be cool to make both of this functions so you can use hold mode to quickly access sub-layer while rocking on IG and to toggle them if you're using Spectra's Isolator as secondary controller in setup with your custom effect mapping engine.

Isolator FX page:



For those who never had a chance to use an isolated effects before, their purpose is to apply an effect on just one isolated frequency of the mix which is in this case High, Mids and Lows or any combination of them in general.

To understand how it works please read this DJTT blog: http://www.djranking s.com/2013/01/0...ng-in-traktor/

For the first time you enter this page you might want to hit the 'Set EQ' buttons (see pic) which will prepare your EQ's for ether C or D before using the Isolator. What this button does is to activate all EQ band kill buttons for decks C and D and deactivate them for decks A and B in case they were engaged before. The six dimly red buttons at each side are your Isolator EQ bend active buttons, once the any of frequencies is active that button will start to flash in green to indicate. Hitting your 'Set EQ' button again works as Isolator EQ reset feature.
As you know by now the way my Isolator works is by duplicating desired track in to corresponding deck which in this case is A>C and B>D so I made two buttons that does just that in this page. Once the button is pressed and deck gets it's copy this button will start to flash in the beat (hitting that button again stops the track in isolator deck if track was playing). There is also an individual sync button for both of Isolators located under the deck duplicator buttons. The bottom line:

Copy A to C > Active Isolator EQ band > focus FX unit to deck C > start mashing

The EQ adjust deck C and D:



I made this mode for setups for people who don't pack four channel mixers but still need some basic control over EQ bands for Isolator. You'll find third side button on both sides as shift state which combined with EQ adjust buttons sets volume to ether 0% or 50%. Also, I made some nice indication using Spectra's animation brightness velocity to display amount for each frequency and center detent as well as full EQ.

FX Unit focus selector:

What it basically does is to select all four units for that deck leaving other decks disengaged. Holding Isolator or EQ mode buttons makes this buttons to toggle all four FX units on any deck.

Stewe,
You need to login in order to write on our forum

<< Cancel

Copyright 2012-2023
DJRANKINGS.ORG n.g.o.
Chuo-ku, Osaka, Japan

Created by Ajaxel CMS

Terms & Privacy